Personal tools
The Open Lighting Project has moved!

We've launched our new site at www.openlighting.org. This wiki will remain and be updated with more technical information.

Difference between revisions of "RDM PID Definitions"

From wiki.openlighting.org

Jump to: navigation, search
(Optional Fields)
m (SLOT_INFO)
Line 224: Line 224:
 
  {'get_request': {'items': []},
 
  {'get_request': {'items': []},
 
   'get_response': {'items': [
 
   'get_response': {'items': [
       {'name': 'slots', 'type': 'group', 'items': [
+
       {'name': 'slots',
 +
      'type': 'group',
 +
      'items': [
 
           {'name': 'slot_offset', 'type': 'uint16'},
 
           {'name': 'slot_offset', 'type': 'uint16'},
 
           {'name': 'slot_type', 'type': 'uint8'},
 
           {'name': 'slot_type', 'type': 'uint8'},

Revision as of 09:01, 6 April 2013

Parameter Definitions and OLA

OLA reads the structure of RDM parameter messages at runtime. This allows the users to update PID definitions without upgrading the binaries and also means we can add knowledge of new manufacturer PIDs to the RDM controller software very quickly.

To enable this, we've designed a parameter definition language which allows us to describe the structure of RDM parameter messages in a language-independent manner. This language has the following assumptions:

  • The structure of a message (i.e. # of repeated values and the length of variable sized fields) must be able to be determined solely from the parameter definition and the length of the message. All parameters in E1.20 and E1.37-1 conform to this, as well as every manufacturer parameter I've encountered. This means that only one variable-sized field can be present in each message, and that TLV style messages aren't supported.

To get the full benefits of the definition language, the parameter definitions should also:

  • Use big-endian for multi-byte fields
  • When integer values are used, the values are stores as normal int values, not as ASCII.

The canonical parameter definitions are stored on the http://rdm.openlighting.org site. The data from the site is used to generate an ASCII protocol buffer which is then checked into the OLA codebase and distributed with the tarball. One day we may support automatic updating of the parameter definition files.

You can see the latest pid protobufs at pids.proto and manufacturer_pids.proto. In the tarball the files are in data/rdm/ and they are usually installed into /usr/local/share/ola/pids/.

Adding New Parameters

Parameters are added to the rdm.openlighting.org site by specifying the message structure, as well as properties like the parameter name and PID in a Python file. To get started, clone the rdm.openlighting.org code from http://code.google.com/p/open-lighting/source/checkout?repo=rdm-app. The definitions are found in data/pid_data.py. Once you have edited this file push the change to a public git repo and email the open-lighting list asking for a pull request. Simon will sanity check the new parameters and push them to the rdm.openlighting.org site.

TODO: link to and describe Laruent's site.

Structure

The section describes the syntax of the parameter definition language in the Python representation used by the rdm.openlighting.org site. The protobuf representation is very similar and the concepts are the same for both representations.

The parameter definitions file is just a Python data structure. At the top level there are two variables MANUFACTURER_PIDS and ESTA_PIDS.

MANUFACTURER_PIDS = [
  {'id': <int>,   # the manufacturer ID, written in hex
   'name': <string>,  # the manufacturer name
   'pids': [<parameter_definition>],
  },
  ...
]

ESTA_PIDS = [
  <parameter_definition>
]

Each Parameter Definition takes the form:

{
  'get_request': {'items': [<item>]},
  'get_response': {'items': [<item>]},
  'get_sub_device_range': <int>,
  'name': <string>,
  'set_request': {'items': [<item>]},
  'set_response': {'items': [<item>]},
  'set_sub_device_range': <int>,
  'link': <string>,   # the URL for more information
  'notes': <string>,
  'value': <int>,  # the PID 
}
{get,set}_request
The structure of the GET / SET request. This specifies a list of items which are the fields in the parameter message. See the section below for more details.
{get,set}_response
The structure of the GET / SET response, same structure as the _request fields.
{get,set}_sub_device_range
A value between 0 and 3 which places restrictions on the value of the SubDevice field in the RDM message.
name
The name of the PID, should be in CAPS like the names in E1.20
line
A URL pointing to where this information was obtained, set to the empty string is there isn't one
notes
A text description of what this parameter does. This should be explain to the user how to use the parameter.
value
The parameter ID (PID).

The allowed values for the sub_device_ranges are:

0
ROOT_DEVICE, implies the subdevice field is 0x0000
1
ROOT_OR_ALL_SUBDEVICE, the subdevice field is 0x0000 to 0x0200 or 0xffff
2
ROOT_OR_SUBDEVICE, the subdevice field is 0x0000 to 0x0200
3
ONLY_SUBDEVICES, the sub device field is 0x0001 to 0x0200

If a {get,set}_request field isn't present, this means the parameter doesn't support the GET / SET operation. In that case the corresponding _response field should also not be present. Note that this differs from a _request field which is present, but contains no items. The latter means that the parameter data length is 0.

Items

Items represent the data fields within each message. An item can also be a group of items, which is how repeated fields are supported. There are only two required attributes for an item:

{
  'name': <string>,
  'type': <string>',
}

Item names should be all lower case, with spaces replaced by _ . In OLA, item names are run through CustomCapitalizeLabel() before being displayed to the user. This replaces '_' with ' ' and capitalizes words. For more details see the code in StringUtils.cpp.

The valid item types are:

  • bool
  • uint8
  • uint16
  • uint32
  • int8
  • int16
  • int32
  • string
  • group, a group of items, see below for more details.
  • ipv4, a 32 bit IP address
  • uid, a 48 bit UID.

All multi-byte items are big endian.

Optional Attributes

These are only defined for certain item types.

Labels

Labels can be used with int items (uint8, uint16, uint32, int8, int16, int32) to attach string descriptions to values.

Using DISPLAY_INVERT as an example:

{'name': 'invert_status', 'type': 'uint8',
 'labels': [(0, 'Off'), (1, 'On'), (2, 'Auto')],
}

Labels implicitly restrict the values that the item can hold. In the example above, a value outside the range 0-2 will generate an exception.

Ranges

Ranges are used to limit the values for an int item. Using REAL_TIME_CLOCK as the example:

{'name': 'month', 'type': 'uint8', 'range': [(1, 12)]}

If both ranges and labels are specified, the union of values is used as the set of allowed values for the item.

Multiplier

This is used to shift the decimal point for int items. For example, in PRESET_INFO, the fade times are reported in 10ths of a second.

{'name': 'max_preset_fade_time', 'type': 'uint16', 'multiplier': -1},

Max Size

This limits the maximum size of a string, or the maximum allowed groups in a repeated item. From DEVICE_LABEL:

{'name': 'label', 'max_size': 32, 'type': 'string'}

Min Size

The opposite of max_size, used for strings and groups. From LANGUAGE_CAPABILITIES:

{'name': 'language', 'max_size': 2, 'min_size': 2, 'type': 'string'}

Item Groups

Examples

These examples show how parameters from E1.20 are described using the PID Definitions Syntax.

DEVICE_INFO

A simple example is DEVICE_INFO. This is only defined for GET commands, and returns a message with various mixed-type fields:

 {'get_request': {'items': []},
  'get_response': {'items': [
      {'name': 'protocol_major', 'type': 'uint8'},
      {'name': 'protocol_minor', 'type': 'uint8'},
      {'name': 'device_model', 'type': 'uint16'},
      {'name': 'product_category', 'type': 'uint16'},
      {'name': 'software_version','type': 'uint32'},
      {'name': 'dmx_footprint', 'type': 'uint16'},
      {'name': 'current_personality', 'type': 'uint8'},
      {'name': 'personality_count','type': 'uint8'},
      {'name': 'dmx_start_address', 'type': 'uint16'},
      {'name': 'sub_device_count','type': 'uint16'},
      {'name': 'sensor_count', 'type': 'uint8'}]},
  'get_sub_device_range': 2,
  'name': 'DEVICE_INFO',                                                                                                                                             
  'value': 96},

DEVICE_LABEL

DEVICE_LABEL is defined for GET and SET. This example shows how to limit the length of a string.

 {'get_request': {'items': []},
  'get_response': {'items': [
      {'name': 'label', 'max_size': 32, 'type': 'string'}
  ]},
  'get_sub_device_range': 2,
  'name': 'DEVICE_LABEL',                                                                                                                                            
  'set_request': {'items': [
      {'name': 'label','max_size': 32, 'type': 'string'}
  ]},
  'set_response': {'items': []},
  'set_sub_device_range': 1,
  'value': 130},
}

SLOT_INFO

This example shows how repeated fields work:

 {'get_request': {'items': []},
  'get_response': {'items': [
      {'name': 'slots',
       'type': 'group',
       'items': [
          {'name': 'slot_offset', 'type': 'uint16'},
          {'name': 'slot_type', 'type': 'uint8'},
          {'name': 'slot_label_id', 'type': 'uint16'}
      ]},
  ]},
  'get_sub_device_range': 2,
  'name': 'SLOT_INFO',                                                                                                                                               
  'value': 288},