Using OLA

2007-10-02T03:26:53Z

75.210.232.7:

=== Using LLA ===

[[LLA]] is a utility that allows applications to send and receive DMX using various hardware devices and DMX over IP protocols. Hardware devices and protocols can also be connected together and LLA will route the DMX between the two.

LLA consists of 4 parts:
- the lla daemon (llad)
- the lla client library (liblla)
- various lla plugins (libllaX)
- example programs (lla_dev_info, lla_patch etc.)

== LLA Terminology ==

Port:
A port represents up to 512 DMX channels that sends data (OUT port) or receives data (IN port). It can be either a physical port on a device or a virtual port created by a DMX over IP protocol.

Device:
A device is a group of ports, for example some devices might have an input and output port.

Plugin
A LLA plugin supports a group of physical devices or a DMX over IP protocol. Example plugins include ArtNet, ShowNet, EspNet, DmxUsbPro, OpenDmx, StageProfi, Dmx4Linux etc. On startup plugins look for the devices they are responsible for and set them up.

Universe:
A universe is a set of 512 DMX channels. Ports can be bound to universes in which case they'll either send the data for the universe (in the case of output ports) or set the values for the universe (for input ports)

Client:
A client is another application that connects to LLA using liblla.

== Using LLA ==

In the general case you want to:
- start the lla daemon
- patch some output ports to universes
- patch an input port or run a client application

=== How to start llad ===

For testing run llad in non-forking, log to stdout, debug level 3:

<code><pre>
llad -d 3 -f -s
</code></pre>

LLA is a daemon and some small apps that uses it. The daemon '''llad''' must be started as root.

=== How to make an interface ready to use ===
Before an interface (e.g. a USB dongle) can be used, a ''port'' on a ''device'' must be ''patched'' (assigned) to a ''universe''.

First you can use the command '''lla_dev_info''' to look up which number the desired interface and port has.

Then the command '''lla_patch''' can be given the numbers just found and the desired universe, so they get connected.

Finally the setup can be tested with '''lla_dmxconsole''' or '''lla_dmxmonitor''' to set or receive DMX values.

Command line options can be seen [http://nomis52.net/?section=projects&sect2=lla&page=llatools here].

[[Category:Articles]]

Using OLA

2007-10-02T03:22:20Z

75.210.232.7:

=== Using LLA ===

[[LLA]] is a utility that allows applications to send and receive DMX using various hardware devices and DMX over IP protocols. Hardware devices and protocols can also be connected together and LLA will route the DMX between the two.

LLA consists of X parts:
- the lla daemon (llad)
- the lla client library (liblla)
- various lla plugins (libllaX)
- example programs (lla_dev_info, lla_patch etc.)

== LLA Terminology ==

Port:
A port represents up to 512 DMX channels that sends data (OUT port) or receives data (IN port). It can be either a physical port on a device or a virtual port created by a DMX over IP protocol.

Device:
A device is a group of ports, for example some devices might have an input and output port.

Plugin
A LLA plugin supports a group of physical devices or a DMX over IP protocol. Example plugins include ArtNet, ShowNet, EspNet, DmxUsbPro, OpenDmx, StageProfi, Dmx4Linux etc. On startup plugins look for the devices they are responsible for and set them up.

Universe:
A universe is a set of 512 DMX channels. Ports can be bound to universes in which case they'll either send the data for the universe (in the case of output ports) or set the values for the universe (for input ports)

Client:
A client is another application that connects to LLA using liblla.

== Using LLA ==

In the general case you want to:
- start the lla daemon
- patch some output ports to universes
- patch an input port

=== How to start llad ===

LLA is a daemon and some small apps that uses it. The daemon '''llad''' must be started as root.

=== How to make an interface ready to use ===
Before an interface (e.g. a USB dongle) can be used, a ''port'' on a ''device'' must be ''patched'' (assigned) to a ''universe''.

First you can use the command '''lla_dev_info''' to look up which number the desired interface and port has.

Then the command '''lla_patch''' can be given the numbers just found and the desired universe, so they get connected.

Finally the setup can be tested with '''lla_dmxconsole''' or '''lla_dmxmonitor''' to set or receive DMX values.

Command line options can be seen [http://nomis52.net/?section=projects&sect2=lla&page=llatools here].

[[Category:Articles]]

wiki.openlighting.org - User contributions [en]

Using OLA

Using OLA